CAS OpenIR
Role of melt pool boundary condition in determining the mechanical properties of selective laser melting AlSi10Mg alloy
Xiong, Z. H.1; Liu, S. L.2; Li, S. F.1; Shi, Y.3; Yang, Y. F.1; Misra, R. D. K.4
2019-01-07
Source PublicationMATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
ISSN0921-5093
Volume740Pages:148-156
AbstractWe describe here a comprehensive study on the effect of cellular structure and melt pool boundary (MPB) condition on the mechanical properties, deformation and failure behavior of AlSi10Mg alloy processed by selective laser melting (SLM). The morphology of melt pool (MP) on the load bearing face of tensile samples was significantly different with build directions. It resulted in different mechanical properties of the samples with different build directions. Furthermore, the microstructure analysis revealed that the MP in the SLM AlSi10Mg alloy mainly consisted of columnar alpha-Al grains which were made of ultra-fine elongated cellular structure. Electron back-scatter diffraction (EBSD) analysis revealed that the long axis of cellular structure and columnar grains were parallel to < 100 >, which resulted in < 100 > fiber texture in SLM AlSi10Mg alloy. However, Schmid factor calculation demonstrated that the anisotropy of mechanical properties of the SLM AlSi10Mg alloy built with different direction was mainly dependent on the distribution of MPB on the load bearing face, and not texture. The defects including pores, residual stress and heat affected zone (HAZ) located at MPB made it the weakest part in the SLM AlSi10Mg. The sample built along horizontal direction exhibited good combination of strength and plasticity and is attributed to the lowest fraction of MPBs that withstand load during tensile. MPB had strong influence on the mechanical properties and failure behavior of SLM AlSi10Mg built with different directions.
KeywordSelective laser melting AlSi10Mg alloy Melt pool boundary Cellular structure Anisotropy
DOI10.1016/j.msea.2018.10.083
Language英语
WOS KeywordHEAT-TREATMENT ; MICROSTRUCTURE ; QUANTIFICATION ; DISLOCATIONS ; BEHAVIOR ; PHASE
Funding ProjectNational Key Research and Development Program of China[2018YFB1105100] ; Key Research Program of Frontier Sciences, Chinese Academy of Sciences[QYZDB-SSW-JSC045] ; National Youth Thousand Plan Program
WOS Research AreaScience & Technology - Other Topics ; Materials Science ; Metallurgy & Metallurgical Engineering
WOS SubjectNanoscience & Nanotechnology ; Materials Science, Multidisciplinary ; Metallurgy & Metallurgical Engineering
Funding OrganizationNational Key Research and Development Program of China ; Key Research Program of Frontier Sciences, Chinese Academy of Sciences ; National Youth Thousand Plan Program
WOS IDWOS:000453494500015
PublisherELSEVIER SCIENCE SA
Citation statistics
Document Type期刊论文
Identifierhttp://ir.ipe.ac.cn/handle/122111/27572
Collection中国科学院过程工程研究所
Corresponding AuthorYang, Y. F.
Affiliation1.Chinese Acad Sci, State Key Lab Multiphase Complex Syst, Inst Proc Engn, 1 Zhong Guan Cun North 2ndSt, Beijing 100190, Peoples R China
2.Shanghai Tiao Tong Univ, Inst Adv Steels & Mat, Sch Mat Sci & Engn, Shanghai 200240, Peoples R China
3.Lanzhou Univ Technol, State Key Lab Adv Proc & Recycling Nonferrous Met, 287 Lan Gong Ping Rd, Lanzhou 730050, Gansu, Peoples R China
4.Univ Texas El Paso, Lab Excellence Adv Steel Res, Mat Sci & Engn Program, Dept Met Mat & Biomed Engn, 500 W Univ Ave, El Paso, TX 79968 USA
Recommended Citation
GB/T 7714
Xiong, Z. H.,Liu, S. L.,Li, S. F.,et al. Role of melt pool boundary condition in determining the mechanical properties of selective laser melting AlSi10Mg alloy[J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,2019,740:148-156.
APA Xiong, Z. H.,Liu, S. L.,Li, S. F.,Shi, Y.,Yang, Y. F.,&Misra, R. D. K..(2019).Role of melt pool boundary condition in determining the mechanical properties of selective laser melting AlSi10Mg alloy.MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,740,148-156.
MLA Xiong, Z. H.,et al."Role of melt pool boundary condition in determining the mechanical properties of selective laser melting AlSi10Mg alloy".MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING 740(2019):148-156.
Files in This Item:
There are no files associated with this item.
Related Services
Recommend this item
Bookmark
Usage statistics
Export to Endnote
Google Scholar
Similar articles in Google Scholar
[Xiong, Z. H.]'s Articles
[Liu, S. L.]'s Articles
[Li, S. F.]'s Articles
Baidu academic
Similar articles in Baidu academic
[Xiong, Z. H.]'s Articles
[Liu, S. L.]'s Articles
[Li, S. F.]'s Articles
Bing Scholar
Similar articles in Bing Scholar
[Xiong, Z. H.]'s Articles
[Liu, S. L.]'s Articles
[Li, S. F.]'s Articles
Terms of Use
No data!
Social Bookmark/Share
All comments (0)
No comment.
 

Items in the repository are protected by copyright, with all rights reserved, unless otherwise indicated.